Product ID:EA 9395 PART A
MSDS Date:09/29/1988
FSC:8040
NIIN:00N015073
Kit Part:Y
MSDS Number: BKPSC

Emergency Phone: 510-458-8000

Info Phone: 510-458-8000

Cage: 33564

Telephone: 202-483-7616

Cage: 33564

EPOXY RESIN SYSTEM

SILICA, AMORPHOUS

CAS: 7631-86-9

Fraction By Weight: <30%

OSHA PEL 20 MPPCF (MFR)

ACGIH TLV: 20 MPPCF (MFR)

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:SKIN AND EYE IRRITATION. POSSIBLE SKIN
SENSITIZATION.
Explanation of Carcinogenicity:CRYSTALLINE SILICA-IARC 2B.
Effects of Overexposure:RASH OR REDNESS OF SKIN.

First Aid:FLUSH SKIN & EYE CONTACT WITH PLENTY OF WATER FOR AT LEAST 15
MINUTES. WASH SKIN THOROUGHLY WITH SOAP & WATER OR HAND CLEANER. DO
NOT USE SOLVENTS. REMOVE SOILED CLOTHING & WASH BEFORE REUSE. IF
IRRIT ATION PERSISTS, SEE MD. INGEST: CALL MDIMMED . INHAL: REMOVE
TO FRESH AIR. SUPPORT BREATHING (GIVE O*2/ARTF RESP) .

Flash Point:>300F,>149C
Extinguishing Media:DRY CHEMICAL OR HALON FIRE EXTINGUISHER, OR WATER
SPRAY, FOAM OR FOG.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:DENSE SMOKE AND TOXIC GASES MAY BE
LIBERATED.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES AND SAFETY
GLASSES. SCRAPE UP AND TRANSFER TO METAL CONTAINER. WIPE UP
REMAINING RESIDUE WITH SOLVENTS, OBSERVING SOLVENT FLAMMABILITY
CAUTIONS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:KEEP COOL IN ACCORDANCE WITH LABEL
INSTRUCTIONS. STORE AT ROOM TEMPERATURE (77F) FOR 12 MONTHS.
Other Precautions:FOLLOW RECOMMENDED CURING SCHEDULE.

Respiratory Protection:NOT NEEDED WITH GOOD INDUSTRIAL VENTILATION.
NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR EXPOSURE OF CONCERN
.
Ventilation:LOCAL EXHAUST RECOMMENDED.
Protective Gloves:IMPERVIOUS PLASTIC OR RUBBER.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:AS NEEDED TO PROTECT SKIN AND CLOTHING.
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING.
Supplemental Safety and Health
CNDTNS (POLYM): CURING SURFACES TO BE BONDED. FAILURE TO OBSERVE
CAUTION MAY RESULT IN EXCESSIVE HEAT BUILD-UP WITH THE RELEASE OF
TOXIC GASES.

HCC:N1
Boiling Pt:B.P. Text:DECOMPOSES
Vapor Pres:<0.01
Spec Gravity:>1
Appearance and Odor:VISCOUS, BLUE PASTE WITH SLIGHT ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:NOT APPLICABLE.
Hazardous Decomposition Products:CO, NO*X, ALDEHYDES, ACIDS AND
UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:AVOID MIXING RESIN & CURING AGENT IN
BATCHES >1 LB TOTAL. DO NOT HEAT MIXED ADHESIVE ABOVE 125F UNLESS
(SEE SUPP DATA)

Waste Disposal Methods:DISPOSE OF AS HAZARDOUS WASTE ACCORDING TO
FEDERAL, STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.